Luxury & Precision P6 64GB PCM1704K R2R DAC Lossless Bluetooth HiFi Audiophile Portable Music Player DAP
The whole machine is equivalent to the use of 2 PCM1704K chips ideal dynamic, SNR 118dB.
The whole machine is equivalent to the use of 4 PCM1704K chips ideal dynamic, SNR 120dB. Increase circuit area, accommodate more resistors and components, improve hearing and dynamics.
The whole machine is equivalent to 8 PCM1704K chips ideal dynamic, SNR 123dB, Bluetooth audio with protocol stack, more FPGA LUT. Improved listening and dynamics, improved operability and ease of use, increased and optimized Bluetooth audio.
Full resistance network, discrete R2R DAC
Innovative 24 Bit full resistance network discrete R2R DAC portable player.
One over ten thousand
Hundreds of one-millionth of a resistor carefully selected to form a discrete R2R DAC network.
R2R the beautiful sound can also burst
The whole machine is equivalent to using 8 PCM1704K chips in parallel for ideal dynamics, and R2R the beautiful sound can also burst.
0 background noise
The SNR of the whole machine is higher than 123dB, 0 background noise, and good news to low resistance balanced armature earphones.
Simple non-touch operating system
Less interference, less power consumption, leaving more power for artificial circuits.
Optimize Bluetooth with protocol stack
A normal Bluetooth clock is a clock that is recovered after parsing data received wireless. The Bluetooth clock of P6 is directly generated by the stop-moment crystal vibration of P6 processed by FPGA, and then the parsed audio data is aligned to the accurate clock generated by FPGA and sent to DAC for lower jitter.
Volume control system
Self-developed lossless - electronic switch matrix volume control system, lower signal loss, easier to use.
The original sound reproduction
Full resistance PCM,DSD native decoding, original sound reproduction.
Architecture advantages, sound characteristics
Because of the advantages of the R2R architecture and the flexibility of the discrete components, the sound of the P6 can be particularly fresh and natural, delicate and mellow.
Sound is the whole pursuit of P6
Although the thrust is great, it is particularly friendly to the earphones. In particular, it enhances the control of the balanced armature earphones while meeting the demand of high output current, and it also needs to achieve a natural stretch of hearing.
Display 3.5-inch, IPS screen, resolution 480x320
Body material: aviation aluminum
Rear cover: glass
Main control: 1812C
DAC: Fully discrete R2R decoding
Crystal oscillator: Low phase noise -160dB active crystal oscillator
Op amp: EXCELS V-O
Amp: EXCELS EP-A
Inductance: low internal resistance large current metal alloy inductance
Capacity: 64GB 24 Bit ECC FLASH
Support extended capacity: 512GB micro SD card (TF)
Use charger specifications: DC voltage input range 4.8-5.5V, power adapter to large output current is recommended to use an adapter of 2A or more (compatible with fast charger)
Battery capacity/type: 4000mA/H Lithium battery
Life time: 15 hours (in case of single-end output of non-high bit rate files played at normal volume when the screen is off)
Accessories: data cable, velvet bag, protective film, manual, warranty card
Highest sampling rate support: PCM: 24Bit 384KHz, DSD: 11.2896MHz (DSD256)
Support audio format: APE, AAC, ALAC, FLAC, WAV, MP3, WMA, DFF, DSF, AIFF, SACD-ISO
Audio interface: 3.5mm single-ended headphone interface (switchable LO, PO, SPDIF), 4.4mm balanced headphones interface (switchable LO, PO), USB-TYPE C interface (switchable data mode/USB/DAC mode)
Adapted headphone impedance: 8 -300ohm
EQ adjustment: 6 style adjustments
HP output: 2-level gain adjustment
Dop SPDIF: support
Digital filter settings: 6 filter modes (including NOS)
Output phase setting: 0 degrees/180 degrees
USB connection mode: MSC mode/Audio mode
USB DAC: support
USB Audio delay setting: long delay mode/short delay mode
DSD decoding settings: native DSD mode / DSD to PCM mode (for adaptation to decoders that only support D2P)
3.5mm single-ended line output performance parameters
SNR: >123dB (single-ended)
Dynamic range: >118dB (single-ended)
Distortion + noise: <0.003%
Frequency response: 20Hz-20KHz ± 0.8dB
Channel separation:> 98dB 10K load
Single-ended line output level: 2.45Vrms/1.55Vrms/ switchable design
4.4mm balanced line output performance parameters
SNR: >123.5dB (balanced)
Dynamic range: >118.5dB (balanced)
Distortion plus noise: <0.003%
Frequency response: 20Hz- 20KHz ± 0.8dB
Channel separation: > 115dB 10K load
Single-ended line output level: 4.9Vrms/3.1Vrms/ switchable design
P6 earphone output part of performance parameters (3.5mm single-ended output)
Maximum output power: @ 16ohm 330mW (distortion rate <0.0039% of on-load power)
Maximum output power: @32ohm 180mW (distortion rate <0.003% of on-load power)
Maximum output power: @300ohm 20mW (distortion rate <0.003% of on-load power)
Dynamic range: >118dB
Distortion + noise: <0.003% @32ohm load
Frequency response: 20Hz -20kHz ± 0.8dB
Output impedance: 0.2 ohm
Channel separation:> 75dB @32ohm load
Output voltage (to high volume): high gain 2.45Vrms, low gain 1.55Vrms
P6 earphone output part of performance parameters (4.4mm balanced output)
Maximum output power: @32ohm 700mW (distortion rate <0.003% of on-load power)
Maximum output power: @100ohm 240mW (distortion rate <0.003% of on-load power)
Maximum output power: @300ohm 80mW (Distortion rate <0.003% of on-load power)
SNR: > 123.5dB
Dynamic range: >118.5dB (balanced PO)
Distortion + noise: <0.003%@32ohm
Frequency response: 20Hz-20KHz ± 0.8dB
Output impedance: 0.4ohm
Channel separation:> 113dB 32ohm load
Output voltage: high gain 4.9Vrms, low gain 3.1Vrms
Bluetooth technical specifications
Bluetooth version: 5.0
Supported protocols: LDAC, APTX, APTXHD, APTXLL, AAC, SBC
Transmission direction: Bluetooth of P6 is the receiving end
Transmission distance: within 15 meters of unobstructed open space
Bluetooth audio clock source: the clock generated by the FPGA is used as the clock source